Other Tractor Accessories
Accessories
 

Implement Accessories

TILLER DEPTH CONTROL WHEEL (for Shallow tillage)

One of the challenges people face with these high-speed tillers is getting them to till at consistently SHALLOW depths, which is desirable for weed control. We now manufacture this handy little gauge wheel assembly, which inserts into the same little receiver under the tiller hood that the Tiller Transport wheel and Hiller/Furrower mount into. The wheel can be adjusted in two ways: By running the 2 large nuts up or down the threaded rod (requires a 1 1/8” wrench), or by moving the wheel unit up or down on the mounting frame (4 sets of holes, requires qty. 2 – 13mm wrenches—NOTE: these fasteners are not quite tight when we ship this accessory, because we figure you’ll probably be adjusting it).

Tilling depth can be adjusted in the range of 0 to 3 inches deep. (Adjustments will vary depending on tractor wheel size, soil type, etc…you just have to play with it a bit.) The 2” wide wheels do make a couple small tracks behind the tiller, but this is typically not an issue when using the tiller for weed control. Fits BCS and Grillo tillers (although more requested by BCS users, since the Grillo tillers do a better job maintaining a relatively shallow tilling depth due to their more-adjustable depth-setting design).

  • Manufactured by Earth Tools
  • Item TLR DPTH WHL: $55 $50


TILLER TRANSPORT WHEEL

When transporting the tractor with tiller implement installed, this wheel holds tiller up off the ground. Especially good for transporting longer distances over concrete, asphalt, gravel, etc.

  • Item 9C7012 (WHEN ORDERING, SPECIFY IF IT NEEDS TO FIT A BCS OR GRILLO TILLER!!): $40 $36


BOX SCRAPER ENDS (Fit 36” Dozer/Scraper Blade)

This Earth Tools Exclusive kit converts the BCS brand Dozer/Scraper Blade to a Box Scraper (also called a “Grader Box”)…EXTREMELY handy for grading of dirt or gravel. Box Scraper Ends attach at each end of blade with 2 bolts & nuts each, so removal or installation is only a few minutes. (If you are purchasing a new 36” blade AND a Box End kit from us at the same time, we will pre-drill the mounting holes needed in the blade at no extra cost.

If you are purchasing the Box End kit for an existing blade you already have, you will have to drill the mounting holes yourself [requires a drill with a 13/32 drill-bit].)

  • Box End Kit (Item ET0172): $80 $70

LEVELING PLATE (for 36” Dozer/Scraper Blade)

We now offer another Earth Tools Exclusive Accessory: Since the 36” Dozer/Scraper blade does not offer any “rotational float”. this becomes a problem when used on a tractor with larger-than-standard wheels: anytime you “pivot” the blade to one side, one side of the blade is higher than the other, because of the “tilted” angle the of tractor down towards the blade when large wheels are used. So, we have devised a “Leveling Plate”, which offsets the blade frame mounting to the implement mount of the tractor, and thus keeps the horizontal plane of the blade level. The plate has 3 different offset positions to handle any wheel height.

  • Leveler Plate (Item ET0170): $34 $29

3-POINT-HITCH ADAPTER for Non-PTO-powered tools


ET 1006 3-point hitch adapter

  • Item ET 1006: $160 $150

This adapter allows many of our Non-PTO-Driven implements (such as plastic mulch layers, cultivators, bedshaper, etc.) to be adapted to a small 4-wheel tractor with a Category 1, 3-point hitch. Does not include any hitch pins. NOTE: since our implements are designed for use with a walk-behind tractor, the extra weight and traction of a 4-wheel tractor COULD potentially damage the implement. Therefore, attaching any of our implements to a 4-wheel tractor VOIDS the implement warranty.